歡迎訪問揚州新銘豐科技有限公司企業官網!
致力開發高科技、高附加值的產品
客戶的需求就是我們的目標
切割測試機XMFQ-125-E
操作步驟:operation step:
第一步:確定并輸入砂輪直徑和工件直徑;
Step 1,make confirm and set the cutting disc diameter and workpiece
Diameter;
第二步:安裝工件,點按手動進料,工件會自動往前送;
Step 2,place the workpiece into the feeding rack and then click the manual and manual feeding,the workpiece will be fed forward;
第三步:點位置回零;切記回零時,工件不要超過砂輪片。
Step 3,return the point position to zero;Remeber that the workpiece shoul的not exceed the cutting disc when returning to zero.
第四步:點按手動下刀,法蘭距離工件大約2mm 停止,點擊下限位保存;
Step 4,click the manual lower the cutting disc,stop when the flange is away from the workpiece,click the the point lower limit saving;
第五步:按手動抬刀,法蘭*下方與工件*上方距離應大于工件直徑1-2mm,點末刀位保存;
Step 5,press manual cutting disc lifting;the distance between the bottom of the flange and the top of the workpiece should be morn1-2mm than the workpiece diameter,click the save the end cutting position;
第六步:點手動抬到至工件上方,點擊待切位保存;
Step 6,press manual lifting to lift the cutting disc above the workpiece,
Then click the save the point to be cut;
第七步:點擊自動,然后按下綠色啟動按鈕;
Step 7,click Auto then press the green start button.
切割測試機XMFQ-125-E
操作步驟:operation step:
第一步:確定并輸入砂輪直徑和工件直徑;
Step 1,make confirm and set the cutting disc diameter and workpiece
Diameter;
第二步:安裝工件,點按手動進料,工件會自動往前送;
Step 2,place the workpiece into the feeding rack and then click the manual and manual feeding,the workpiece will be fed forward;
第三步:點位置回零;切記回零時,工件不要超過砂輪片。
Step 3,return the point position to zero;Remeber that the workpiece shoul的not exceed the cutting disc when returning to zero.
第四步:點按手動下刀,法蘭距離工件大約2mm 停止,點擊下限位保存;
Step 4,click the manual lower the cutting disc,stop when the flange is away from the workpiece,click the the point lower limit saving;
第五步:按手動抬刀,法蘭*下方與工件*上方距離應大于工件直徑1-2mm,點末刀位保存;
Step 5,press manual cutting disc lifting;the distance between the bottom of the flange and the top of the workpiece should be morn1-2mm than the workpiece diameter,click the save the end cutting position;
第六步:點手動抬到至工件上方,點擊待切位保存;
Step 6,press manual lifting to lift the cutting disc above the workpiece,
Then click the save the point to be cut;
第七步:點擊自動,然后按下綠色啟動按鈕;
Step 7,click Auto then press the green start button.
在線留言
ONLINE MESSAGE
相關產品
RELATED PRODUCTS